“Lights out” cutting enables you to process your parts at all hours of the day, even during unmanned evening shifts.
Lights Out Nesting
- A metal fabricating facility during the day is a noisy, bustling place. Lift trucks are zooming by, and CNC machines are cutting away. Production runs at full speed. But typically, in the evening, the machines are shut down and all grows quiet until the next morning. The machines could run longer hours, but the cost of keeping the facility staffed for a full late-night shift is not justified in today’s uncertain economy.
- So how can a metal fabricator ensure that overhead costs stay low while production capacity keeps up with the order book? The answer is “lights out” manufacturing. In this scenario, a manufacturing facility relies on material-handling automation to move blanks of sheet metal or plate onto the cutting bed of a CNC machine, usually a laser cutting machine, and to remove the skeleton and cut parts after the cutting is done. The entire process repeats itself once the previous job has been removed from the bed.
- In the most advanced lights-out manufacturing environments, a flexible manufacturing system (FMS) comprises a single or a group of CNC machines, a storage tower for raw material inventory, and a line controller to coordinate the delivery of the blanks, the cutting job, and removal of the parts. The FMS approach also usually entails more advanced part-sorting options, instead of simply dropping cut parts in one single area.
- On the other end of the spectrum is the use of a loader/unloader. This is typically used for a single machine on which the automation simply loads one sheet after another. This arrangement requires that the blank be stacked on the loader in the order it will be needed.
- Of course, nothing is totally infallible. Even for those companies with the most advanced lights out operations, the emergency phone call in the middle of the night to an equipment operator sometimes happens. A part might tip up and collide with the laser cutting head, or material inconsistencies may cause a cutting problem.
- Advanced nesting systems can help prevent those scenarios and eliminate the late-night phone calls. Software features are designed to take steps to ensure potential collisions are avoided. Setting up a repeatable and consistent process is key. If done correctly, the manufacturer can schedule the work in advance and run the cutting machine over an entire shift—and even over an entire weekend with the right combination of FMS and nesting software capabilities.
Avoiding the Chance of a Collision
For example, for cutting contours, the nesting software determines the optimal leadin and leadout point for the cutting head, so it will be clear when the final cut is made on the part, steering clear of any potential tip-ups. The attempt to optimize the cutting flow also ensures the parts are cut quickly, keeping the head down and cutting as much as possible.
In general, nesting software attempts to keep the cutting head away from previously cut areas to avoid opportunities for tip-ups. In the event an optimized cutting path calls for a torch head to move over a cut area, instructions tell the head to retract sufficiently so that it can travel safely over the cut part.
Advanced software packages actually create a designated “halo” around cut parts, so that that cutting head steers clear of the area around the part as well. Some software packages allow machine operators to create their own fixed value for the halo manually. For instance, a CNC cutting machine with a contact head might require a larger halo than one with a non-contact cutting head.
Tabbing Keeps the Parts Situated
Used mostly for small parts that can tip up with the slightest encouragement, tabbing is done automatically in nesting programs, with a little input from the machine operator. The operator provides the tab and part parameters, then parts which fall within these parameters are automatically tabbed.
Nesting programs also include manual overrides of dynamic nesting rules and predetermined operator parameters for problem parts, such as a long, thin part that risks falling into the slats after it has been cut. An operator can go into the software and dictate that tabs are placed on this particular part anytime it is cut.
Sorting It All Out
With most software packages, the person responsible for sorting parts from the skeleton can reference a visual image on the computer screen and use that to separate parts onto assigned pallets. The graphical layout of the sheet on the computer screen likely contains a part number, which can help differentiate between two similar-looking parts.
Some advanced nesting software might have more than the simple part number to help with sorting efforts. A feature such as a color-coded graphic of the nest can simplify and speed up the offloading process. Each individual part is colored differently, making it easier to identify all of the parts, even those that might look the same.
So not only can advanced nesting software keep the automated fabricating operations up and running, it also can help with the back-end part organization. The software is a valuable tool for those metal fabricators that find the only way they can be competitive is with their automation investment.